How to Tile Laundry Room Floor? A Definitive Guide!

Laundry rooms come in two varieties: those you conceal in your basement and those you take magazine photos of. In a perfect world, everyone would possess the latter. But designing the laundry room of your dreams can be a big task. Nonetheless, tile can have a significant impact. Hence, how to tile the laundry room floor is something you’re curious about.

Assemble the necessary materials, take out the existing flooring, and use a hammer drill to detach the tile from the cement board base. Grease pencils, cut and install tile with a Modifications wet saw, and grout floor tiles. Let the grout dry for 72 hours after sealing it with a brush.

The detailed guide on how to tile the laundry room floor explained below will make your weekly routine brighter. You will be prepared to push “refresh” on your workspace to embrace a springtime makeover that makes performing chores exciting once you see the elegance and adaptability of laundry tiles, I guarantee it.

How to Tile Laundry Room Floor

One of the rooms in a house that is most susceptible to disturbances is the laundry room. It is susceptible to fractures from rolling and shaking washers and dryers as well as stains, spills, buildups, mold and mildew from device leaks, and other damage. Keeping this in mind, furnishing the area might be difficult, especially because there are so many options available.

You need to choose the perfect tile for your laundry room not only because it looks good, but also because it is practical and pleasant to use. It must be tough and able to tolerate heat, humidity, and wetness in addition to normal use and deterioration.

The selection of your finishes can emphasize the design of your laundry room. Whichever the size of your room, there are wonderful options for flooring and walls thanks to the range of tiles that are available. The tile is quite durable in addition to being water-resistant. It works well in areas with a lot of moisture, like your laundry room.

Step-by-step Tile Floor Installation

1. Assemble All Materials:

Having the correct equipment can make a big difference, and this tile installation task is no exception! Here is everything you needed to install the new tile on your laundry room floor:

• Tile (I chose this ceramic tile.)
• Spacers and Levelers
• Tile Saw
• Tile Cutter
• Grease Pencils
• Trowel
• Hammer Drill with Chisel Bit
• Drill + Mixing Paddle
• Tile Mortar
• Grout
• Grout Float
• Measuring Tape
• Shop Vac
• Sponge + Bucket
• Grout Sealer

How to Calculate the Number of Tiles Required:

You need to determine how many tiles you will need before looking at even one sample. You begin by determining the size of your laundry room. In order to get the square footage, you multiply these figures together.

But you could not just go out and buy 45 feet of tile. Keep in mind you had extra so you could account for errors, spots where you need to utilize only part of a tile, etc. In case one or several of the tiles you placed were accidentally broken, you also intended to have a few tiles left over for later.

The specialists typically advise overspending on tile by 10% to 20% to be cautious. Check your store’s return policy before making a purchase to see if they allow you to return any entire packages of tile if you don’t wind up using them.

2. Take Out the Current Flooring:

Firstly you must take out the old tile in order to install your gorgeous new tile! Start by removing the baseboards by prying them apart from the wall with a chisel and a hammer. It is simpler to take on the tiling once the moldings had been removed from the way.

Then break and remove the tile from the flooring base using a chisel bit on a hammer drill, working from the back left side towards the entryway. The tile floor will quickly be destroyed by the hammer drill.  The entire tile can be taken out in around 30 minutes. Hours may have been needed to use a hammer and chisel.

3. Choose a Tile Arrangement:

You couldn’t just begin tiling the floor when your area was prepared and ready to go. Choosing your tile’s arrangement is the initial step. You can lay out the real tile to determine how it would look on the floor if you have a relatively small area to work with. If you chose to overlap each tile by a third, row four is a repetition of row one after three rows have been laid.

You should start tiling from the rear of the room and work your way out due to the restricted size. But, you must take care to avoid leaving a tiny strip of tile next to the room’s door. That would not be attractive. If feasible, make the initial row of tiles that visitors view upon entering the space as wide as possible. Starting from the back, you aligned the tiles, ignoring the 1/3 overlap, to make absolutely sure you could skip a short strip of tile next to the door. To test if you would wind up with a whole tile, you can add the separators and work your way toward the entryway.

It will turn out that you might start with a full-width tile in the rear of the laundry room and finish there with a tile that is approximately the entire width as well. If not, you can remove the first row of tiles from the laundry room’s back wall so that the entry will have a full-width tile.

4. Make the Mortar and Apply It:

It’s time to start really putting the tile now that the layout has been established! Mastic can be substituted with conventional tile mortar. Although mastic is effective with ceramic tile, mortar is a little more tolerant and tends to dry a little more slowly. The most likely material used while tiling a wall is mastic.

Following your 2.5-gallon bucket purchase of pre-mixed mortar, you would review the tile trowel guidelines for that specific product. It was advised that I employ a trowel with 1/4″ x 1/4″ notches for my tile width and my specific mortar. Usually speaking, you will need deeper notches in your tile trowel for larger tiles. It is crucial to adhere to the instructions on your specific mortar or mastic.

I made the decision to use 1/16′′ for the tile spacing. This results in an attractive, extremely thin grout line, but it only works if your tiles are precisely the same size. Certain natural stones are not consistent, unlike the majority of ceramic tiles. I would have decided to space my tiles 1/8′′ apart if they were not all uniform.

5. Trim and Install the Tile:

For this particular tile arrangement, the majority of your incisions should be straight lines parallel to the tile’s length. You may discover that certain tiles are unevenly chipped and snapped while others are readily scored and snapped. Fortunately, snapping and scoring these tiles is simple.

The tile can be put in the tile snapper once you have measured it and decided where to cut it. Moreover, you can score the surface repeatedly to make a tiny groove, then use the handle to press down on the tile and shatter it at the line. You won’t be having any damaged tiles because of how well this worked.

You are required to make a few incisions for this project that a tile snapper could not handle, including cuts around door jams. Use a Ryobi wet saw for this. This saw is reasonably priced and does a nice job. Straight cuts are simple thanks to the fence’s adjustable features. In contrast to some of those enormous tile saws that weigh more than 100 pounds, it is also lightweight and portable.

You will be discovered that marking the tiles with grease pencils before cutting them with a wet saw is one useful technique. While using the wet saw, a pencil mark will simply wash away, but the grease pencil will remain visible even after being wet. You will discover that in order to use your spacers and levelers, you would be required to remove the door if you didn’t want to spend the next 24 hours trapped in the laundry room while the tile dried. After the door was taken out, you could complete the last tile!

6. The Tile Needs to Be Grouted:

Tile floor grouting is enjoyable and simple. The procedure is quick, and the tile appears better right away. You may also select grout in Dove Gray. You can mix grout inside a bucket using your cordless drill, a mixer bit, and the directions on the grout bag’s back. Make sure you have plenty of sponges and a pail of clean water available once the grout has been mixed.

When compared to grouting wall tile, grouting floor tile is wonderful. Without having to be concerned about grout dropping off the wall and creating a mess, it is simple to apply a bunch of grout to the tiling and then fill in the grout well with the grout float. With your grout float, you can work the grout into the 1/16′′ space between the tiles, working on about 3 square feet of tile at a time. You should scrape out as much leftover grout as you can once the grout is placed in the area between the tiles.

The grout-covered tile can then be wiped down using a clockwise motion and light pressure using a cloth from the container of water that has been as thoroughly wrung out as possible. After the grout had been applied to the sponge’s two sides, you could bring it out and repeat the procedure. Before the surplus grout is removed after 3 or 4 passes, only the area between the tiles is left with grout.

7. Cover the Grout:

Since you took so much time installing and grouting your tiles, you undoubtedly want to take the necessary precautions to safeguard the grout. The grout can be sealed to do this. Before beginning the sealing process, you let the grout for around 72 hours to cure. Just apply the sealer to the grout lines, returning back every few rows to remove any excess sealer that got on the tile using a dry towel.

After completing the first layer of sealer, you must wait 30 minutes before proceeding with the second coat. After two to three hours of drying alone, it was finished! Once the sealing procedure is finished, you can take pleasure in the brand-new, exquisitely tiled floor of your laundry room.

Design Tip: Choosing Materials

It might be challenging to decide which tile material to use when there are so many possibilities available, including ceramic, porcelain, marble, glass, and limestone. In addition to being sturdy, man-made tiles like porcelain and ceramic also exist in an almost infinite variety. There is always the ideal tile for your task due to the variety of colors, sizes, and finishes available. Stone tiles come in a wide range of natural sources variants as well, but they require different maintenance techniques. There is no single ideal tile; it all depends on the appearance you want to create. There is constantly something new to learn about in The Tile Shop’s extensive collection of tiles, which is always expanding.

Design Tip: Choosing Colors

If your laundry room also serves as a mudroom, it may be a good idea to use non-slip tile that will not reveal dust for the floors to help hide spills. The backsplash in your laundry room is a wonderful location to decorate. A vibrant and cheery color, pattern, or design enlivens the area while being strong and useful. There are numerous alternatives for your laundry room wall tile, including blue, emerald, red, magenta, silver, and even shiny.

Conclusion

Choose from a range of laundry room tile alternatives to finish your room. Because it must tolerate corrosive chemicals, wetness, and heavy foot traffic, laundry flooring is unique. So, rather than putting hardwood or carpet, laundry room floor tiles or laundry room laminate flooring are usually the most popular forms of flooring.

Choose mosaic, penny tile, or herringbone patterns for your farmhouse laundry room flooring. These choices add style to your laundry area without compromising on toughness or usability. You can prioritize both aesthetics and maintenance free, regardless of the flooring you choose for the laundry room. To give your laundry room a classic and lovely finish, consider the following laundry room tile ideas and guide.